Laser cutting has reached a point at which many of those materials previously labeled as &#;difficult&#; can now be cut. Today, modestly powered laser cutters of up to a few hundred watts of cutting/engraving capacity are considered normal in home workshops. The largest laser cutting machines can cut steel, 100 mm thickness, at up to 100 mm/s feed. With the selection of the right methods, even the most difficult materials, such as stainless steel, can be cleanly cut. The lowest-cost machines (under $100), on the other hand, can cut many thin sheets and engrave on a wide spectrum of materials.
If you are looking for more details, kindly visit our website.
Despite the improved capability of laser cutters, there are still good and bad materials for laser cutting, for example: acrylic, plywood, and MDF. Listed below are the most common laser cutting materials:
Acrylic (PMMA) is a transparent plastic material known for its outstanding strength, optical clarity, and stiffness. There are two forms of acrylic: cast and extruded. Extruded sheet is harder to cut because residual stresses result in stress cracking. Slower cutting of extruded acrylic can leave better-looking cut edges. Ventilation is required when laser cutting acrylic because the vapor is an ignition risk and is toxic.
CO2 or diode-pumped is the recommended laser type when cutting acrylic. It is suggested to use the lowest power in cutting acrylic. High power will result in scorching. An 80 W laser should cut 8 mm acrylic at about 5 mm/s and produce high-quality edges, with a minimal heat-affected zone (HAZ). If the blower is set high, rough edges will result&#;the right pressure is the strongest you can blow on your finger, for setup.
Plywood is made from bonded wood veneers. While many forms of plywood are marketed, all plywood can be laser cut. Plywood is bonded with resins and produces toxic gasses when heated. It is therefore recommended to use ventilation when cutting.
Plywoods require high power and fast speeds when performing multiple cuts&#;which may result in an increase in kerf size. Higher blower pressure will result in cleaner cutting and allow higher feed rates. The recommended laser types are CO2 and fiber lasers.
MDF (Medium Density Fiberboard) sheet is an engineered material made with hardwood or softwood residuals. It is not an easy material to laser cut because its density and high adhesive content make it slow to cut and easy to produce staining and soot marking. MDF&#;s high density requires slow cut speeds and results in high HAZ and wide kerfing. It is recommended to use CO2 or a diode-pumped laser when cutting MDF.
When cutting MDF, it is necessary to use the highest power available. An 80 W laser cuts 10 mm MDF at about 3.5 mm/s with scorched and stained edges. The blower pressure also needs to be high. There will be burned residue to blow away, to allow the laser to pass and avoid depositing soot/residues on the optics.
Cardboard is a generic term for heavy paper-based products. It is a low-cost material used extensively for product packaging, modeling, and advertising. All laser types work well with cardboard.
When laser cutting cardboard, it is recommended to maintain ventilation. However, the volume of combustion products will be low, and cardboard has no significant toxicity. Additionally, use moderate power levels and fast feed speeds. Kerfing will also be limited and the HAZ will be small. Blower pressure should be set low, as the material can be lifted by air pressure, but some flow will make for better cut quality.
POM (PolyOxyMethylene, Delrin®, or acetal copolymer) is an engineering material used in applications requiring strength, chemical resistance, and dimensional stability such as machine parts. CO2 lasers give the best results, but a fiber laser can be used for marking/engraving. The POM cuts very cleanly, with little HAZ using a CO2 laser.
When laser cutting POM, it is important to use ventilation because the scorched plastic presents high toxicity. Similar laser settings to those used for acrylic are often recommended although 25% slower feed rates are acceptable. Set to the lowest power that will allow the cut to proceed. An 80 W laser should cut 8 mm Acetal/POM at about 4 mm/s. The blower should also be set to moderate pressure.
A foam is a broad term that refers to materials formed by trapping pockets of gas in a liquid or solid. It encompasses a range of materials, some of which can be laser cut, several of which cannot. Some cuttable examples are: expanded polystyrene or polypropylene foams, Depron modeling foam, foam-cored boards like Gatorfoam, and EVA foam. There is no simple recommendation of a laser type, as foams belong to a range of material types&#;but any laser type is likely to cut well.
Laser cutting of foams requires very low power and high feed rates, good ventilation, and a breathing mask, as most foams release toxic gasses when heated. Blowers should also be set to a low level for thin materials.
Metal is a family of materials requiring high power to cut anything thicker than foil. Some metals work best with fiber lasers or solid-state, but others work with CO2 lasers. Cut quality is a result of laser power, pulsation, beam diameter, focal depth, and light frequency. Metals produce little by way of gas or residues and generally exhibit low toxicity, although normal precautions should still be applied.
Two methods are employed in the laser cutting of metals: reactive laser cutting and fusion cutting. Reactive laser cutting uses an oxygen jet in the cut to accelerate the cutting by oxidation. For thicker steel sections and titanium, the metal is rapidly oxidized and/or melted and then blown out of the cut area. Fusion cutting, on the other hand, is used to cut aluminum, stainless steel, copper, nickel, and tungsten. This technique uses a blend of nitrogen and argon to blow molten metal away from the cut.
A leather is a strong and flexible material that is traditionally made of animal skins, although faux leather (artificial) is now available. CO2 lasers are generally the most effective at cutting leather. Modestly powered lasers will make good cuts in leather, although multiple passes may be required. Laser cutting in leather is clean and leaves no torn or damaged fibers. Laser cutting leather avoids the stress distortion that occurs with even the sharpest hand tools.
Plastic is another broad classification that contains materials that cut well. Some of the plastic materials suitable for laser cutting are polyimide (Kapton®) and polyester (Mylar®) which cut well using diode laser and CO2 lasers respectively. Polycarbonate sheet, on the other hand, can be cut at 1 mm max, but the HAZ yellows and can distort. Polystyrene also cuts cleanly but tends to produce a lot of smoke and releases toxic styrene gas. Cut quality is a result of influences in laser power, pulsation, beam diameter, focal depth, (for thicker cuts), and light frequency (laser type). No two plastics have the same requirements. All plastics produce toxic gas or residues, and these pose serious health risks, so precautions are recommended.
Cork is the bark of the cork oak and is usually used in manufactured sheets. For cork, up to 3 mm thick, the speed of cut should be fairly fast, tens of millimeters per second. Thicker cork mats will require multiple passes for good cutting. Start with quite low power and increase until a smoke-free cut is achieved. The blower should be set to a high level, but not high enough to lift the sheet or cut areas.
Natural textiles such as cotton, silk, and wool are great candidates for laser cutting. Low to moderate power and high feed rates will generally give excellent cut quality. Blower use is beneficial but must be at low pressure to prevent the fabric from being displaced and lifted. Synthetic fabrics can pose some issues as the line between melting the cut line and creating a fire can be quite narrow. There are no general settings that ensure good results. However, synthetic fabrics work well for laser cutting, once stable settings can be achieved.
Paper is very well suited to laser cutting. Any small laser-cutting machine will do a great job with paper, but it&#;s not well suited to larger industrial machines. Paper requires low power settings and high feed speeds, as it cuts very fast. Heavier papers may need slightly lower feed rates. Very clean cuts with no visible HAZ can be made.
The laser cutting settings for each material vary. Table 1 below lists some example:
Laser cutting is a subtractive manufacturing technology that uses a high-power laser beam to melt, burn, or vaporize the material.
The process begins with a design file loaded into the laser cutter software. As the machine starts, the laser cutter moves the beam along the design file&#;s path as instructed by the software to ensure accuracy and repeatability.
With competitive price and timely delivery, JCZ sincerely hope to be your supplier and partner.
The high-intensity laser beam from the laser heats the material, and the designated areas are either melted, burned away, or vaporized, leaving precise and clean cuts.
The beauty of laser cutting lies in its adaptability. The laser cutter settings&#;like the laser's power, speed, and duration&#;are adjustable, making it possible to cut a variety of materials, including wood, acrylic, leather, fabrics, rubber, paper, and metal, with clean and polished cuts.
Typically, if the laser cutter can cut a material, it can also engrave it.
$899.99
View Details
Plastic is also a common material for laser cutting and engraving. They are synthetic materials that come in various colors, thicknesses, and finishes. They can be cut with a smooth edge and a glossy surface by a laser.
Acrylic or plexiglass, is the most popular plastic for laser cutting. By laser cutting acrylic, especially clear ones, you can create beautiful glass-style artwork, such as ornaments, signs, displays, jewelry, and wall art.
However, not all plastics are suitable for laser cutting. Some plastics may contain chlorine or other harmful substances that can produce toxic fumes when heated by the laser. Therefore, it is important to check the composition of the plastic before cutting it with a laser. And always maintain a good ventilation when laser cutting plastics.
Related Reading
Using a laser cutter or laser engraver for cutting metal can be a bit tricky. You will need specific laser types for this purpose. However, laser engravers work extremely well for engraving metal. Metal is a great laser engraver material that allows you to make a wide array of personalized items or engraved gifts.
$1,499.00
View Details
Once you&#;ve practiced a bit with other laser cutting materials and laser engraving materials, you might want to try your hand at leather. It&#;s an expensive material, but the results look amazing. You can create wallets, belts, purses, jewelry (especially bracelets) , keychains and more. You can refer to the laser engraving leather and laser cutting leather guide to get the best practice with processing leather materials using a laser cutter.
Cardboard is one of the most inexpensive and easiest laser cutting materials to work with. Model-building pieces are one of the most common laser cut cardboard projects. Typically, you can choose between corrugated, gray and cellulose cardboard.
Fabric is a newer option for laser cutting materials. Laser cutting and engraving fabric works as a form of digital embroidery. You get similar results in a lot less time. While leather is obviously one type of textile, cotton, nylon, polyester, and silk are all options too.
In most cases, when laser cutting paper, you&#;ll likely be cutting cardboard. However, thick cardstock paper is also excellent material for laser cutting. A creative project to try with paper is custom cards with a laser-cut center scene. These are beautiful and make great gifts.
Rubber is another laser engraving material that can be cut or engraved using a laser machine. Though it is a widely used material for various purposes but is not very common in laser cutting. But with a laser, you can use it for making stamps, keychains, mats, personalized apple watch bands and other items that require rubber.
Laser is the right option for rubber cutting because it offers fine and perfect cutting results. The edges are smooth and perfect, which cannot be achieved by any other method. It can cut various types of rubber, including natural rubber, silicone rubber, and synthetic rubber. However, you need to make sure proper ventilation because of the fumes produced during laser cutting.
Related Reading
Due to its fragile nature, glass is prone to cracking when laser cut. However, glass can still be laser cut using specific laser types. Moreover, when laser engraved, glass is imprinted with beautiful frosted pattern, making it a good laser engraving material for making a variety of decorative items.
Related Reading
If you want to learn more, please visit our website laser trimming machine.